• img1
  • img2
  • img3

+49(0)17685399327

hanna@fcejmdg.com

Product Categories

Contact Us

Dong Guan FCE Prescision Electronics Co.,Ltd

Add:No.5 of Minyi Road, Wusha, Changan Town, Dongguan, Guangdong, China

Contact:Hanna Wang

Mobile:+49(0)17685399327

Fax:0769-81582880

E-mail:hanna@fcejmdg.com

Web:dgfcejm.com

Home > News > Content
Stamping Parts Dedicated To Regular Checks

Stamping Parts parts production is a material molding technology, in recent years, is a new type of metal cold deformation processing methods. Is one of the main methods of metal plastic processing. In the production of Stamping Parts parts, people are using conventional or special Stamping Parts equipment, the power of Stamping Parts, the use of pressure to make the material deformation, and then use the mold plate deformation, to get a certain size of the product parts, then Hebei Stamping Parts parts Manufacturers, in the production of the time, need to pay attention to what the problem, let the following professional manufacturers for our detailed introduction about it!

In the production of Stamping Parts parts, we use the press or die and other engineering equipment, we should pay attention to, we have to use in the normal working conditions, which can effectively prevent the strip can not be transported along the correct positioning of the material , Or can not be in accordance with our scheduled advance in a certain gap feeding. We are sure to die parts of a fastening, note that in the production of Stamping Parts parts, do not change the location of the various molds, once the change will scratch or crush the workpiece surface, so that the workpiece The quality of the impact is very large.

Another point is that when we prepare the material, be sure to comply with technical specifications, pay attention to the precise measurement of the size of raw materials, must be strictly for the raw material inspection and brand inspection. There is also that we are in the production of Stamping Parts parts, we must be on the abrasive and some punches dedicated to the regular inspection to prevent the work parts and guide parts because of long-term operation and wear. Strictly adhere to the Stamping Parts parts of the production of the relevant matters, so as to avoid unnecessary losses.

Stamping Parts is located in the first four major automobile manufacturing process, its importance is self-evident, and Stamping Parts parts as the basis for car body quality assurance, its quality is directly related to the merits of the whole car, each vehicle factory The quality of the consumer's consumption is becoming more and more important, and the quality of the car body is also more concerned. Therefore, it is very important to control the quality of the Stamping Parts parts and whether the quality control method is effective and will decide whether the quality of the automobile body is more and more important. Quality control of Stamping Parts parts. This article will be Stamping Parts parts from the material to the finished product of the entire process of quality control methods are discussed.

Stamping Parts parts can be divided into outer plate, quasi-outer plate and inner plate, as shown in Figure 1. The outer panel refers to the visually easy to find the parts, also known as outer cover, such as the outer cover of the engine cover, the top cover, side Wai outer plate, etc .; quasi-outer plate refers to the visual is not easy to find, but the relevant parts after opening Visible parts, such as the inner cover of the engine cover, the inner door of the door, the inner lid of the trunk, etc .; the inner part refers to the parts that are not concerned or can not be found, such as wheel cover, floor, The Although these Stamping Parts parts of different quality requirements, but their quality control methods are similar.

In the production of Stamping Parts parts, we use the press or die and other engineering equipment, we should pay attention to, we have to use in the normal working conditions, which can effectively prevent the strip can not be transported along the correct positioning of the material , Or can not be in accordance with our scheduled advance in a certain gap feeding. We are sure to die parts of a fastening, note that in the production of Stamping Parts parts, do not change the location of the various molds, once the change will scratch or crush the workpiece surface, so that the workpiece The quality of the impact is very large.


Contact Us
Dong Guan FCE Precision Electronics Co.,Ltd

Address: No.5 of Minyi Rd, Wusha, Changan Town, Dongguan, Guangdong, China

Tel: +49(0)17685399327

Fax: 0769-81582880

E-mail: hanna@fcejmdg.com

Copyright © Dong Guan FCE Precision Electronics Co.,Ltd All rights reserved.
foottop